Are you tired of your toilet paper roll falling off the holder every time you reach for it? Installing a one arm toilet paper holder can solve this problem and add a touch of elegance to your bathroom. In this step-by-step guide, we’ll show you how to install a one arm toilet paper holder in just a few simple steps.
Gather Materials and Tools
Before you start the installation process, it’s essential to gather all the necessary materials and tools. Here’s a list of what you’ll need to complete the installation successfully:
Materials
- One arm toilet paper holder
- Screws
- Drywall anchors
Tools
- Drill
- Screwdriver
- Measuring tape
- Pencil
The one arm toilet paper holder comes with mounting hardware, so you don’t need to purchase any additional items. However, you may need to buy drywall anchors if you’re not mounting the holder on a stud.
Make sure you have all the tools and materials on hand before you begin the installation process. This will save you time and frustration later on.
Locate Studs and Mark Placement
The next step is to locate the studs in your bathroom wall. It’s essential to mount the one arm toilet paper holder on a stud to ensure its stability and prevent it from falling off the wall.
Use a stud finder to locate the studs in your bathroom wall. Once you’ve found the studs, use a measuring tape to determine the desired placement of the one arm toilet paper holder. Mark the location with a pencil.
If you’re not mounting the holder on a stud, use drywall anchors to secure it to the wall. Mark the location of the anchors with a pencil.
In the next section, we’ll cover how to drill holes and install anchor screws.
Now, let’s move on to the next two sections.
Drill Holes and Install Anchor Screws
The next step in the installation process is to drill holes in the wall and install anchor screws if necessary.
Use a drill bit that’s slightly smaller than the screws to drill the holes. If you’re installing drywall anchors, use a drill bit that’s the same size as the anchor.
Insert the anchor into the hole and tap it gently with a hammer until it’s flush with the wall.
Now, screw the holder into the anchor or stud with a screwdriver. Be careful not to overtighten the screws.
Repeat the process for the other side of the holder if necessary.
Install One Arm Toilet Paper Holder
Finally, it’s time to install the one arm toilet paper holder.
Attach the holder to the screws or anchors and adjust it as necessary to ensure that it’s level.
Tighten the screws with a screwdriver, but don’t overtighten them.
Congratulations, you’ve successfully installed a one arm toilet paper holder!
In the next section, we’ll cover some tips for ensuring a level installation.
Conclusion
Installing a one arm toilet paper holder is an easy and affordable way to add convenience and style to your bathroom. By following the step-by-step guide above, you can install a one arm toilet paper holder in no time.
Remember to gather all the necessary materials and tools, locate the studs or install drywall anchors, and attach the holder to the screws or anchors.
With these simple steps, you’ll be able to enjoy a stable and stylish toilet paper holder for years to come.
Locate Studs and Mark Placement
Locating the studs is crucial to ensure that the one arm toilet paper holder is securely mounted to the wall. You can use a stud finder to locate the studs. If you don’t have a stud finder, you can look for signs such as nail heads or dimples in the drywall, or tap along the wall to listen for a solid sound, indicating the presence of a stud.
Once you’ve located the studs, use a measuring tape to determine the desired placement of the one arm toilet paper holder. To ensure the holder is within easy reach, it’s recommended to install it about 26 inches above the floor. Mark the location with a pencil, making sure that both sides of the holder are level.
If you’re not mounting the holder on a stud, you’ll need to install drywall anchors. Use a hollow-wall anchor that is rated to hold at least 50 pounds. Follow the manufacturer’s instructions to install the anchors, and make sure that they are positioned at least 1 inch away from the edge of the drywall to prevent it from cracking.
Drill Holes and Install Anchor Screws
After marking the placement of the one arm toilet paper holder, it’s time to drill holes and install anchor screws if necessary. Use a drill bit that’s slightly smaller than the screws to drill the holes. If you’re installing drywall anchors, use a drill bit that’s the same size as the anchor.
Insert the drywall anchor into the hole and tap it gently with a hammer until it’s flush with the wall. If you’re mounting the holder on a stud, you can skip this step.
Now, screw the holder into the drywall anchor or stud with a screwdriver. Be careful not to overtighten the screws, as this can cause the drywall to crack or the holder to become warped. If you’re not sure if the holder is securely mounted, try pulling on it gently to check.
Repeat the process for the other side of the holder if necessary. Once you’ve installed both sides of the holder, make sure that it’s level. If it’s not level, adjust the screws or anchors until it is.
In the next section, we’ll cover how to attach the one arm toilet paper holder to the screws or anchors.
Install One Arm Toilet Paper Holder
Now that you’ve drilled the holes and installed the anchor screws, it’s time to attach the one arm toilet paper holder to the wall. Here are the steps to follow:
- Insert the screws into the mounting holes on the holder.
- Align the holder with the holes in the wall and gently press it against the wall.
- Use a screwdriver to screw the holder into the anchor or stud. Make sure to tighten the screws just enough to hold the holder securely, but not so much that you damage the wall or strip the screws.
It’s important to ensure that the holder is level to prevent the toilet paper roll from sliding off. Here are some tips to help you achieve a level installation:
- Use a level to check that the holder is straight before screwing it into place.
- If the holder isn’t level, adjust it by loosening the screws slightly and repositioning the holder. Tighten the screws again once the holder is level.
Conclusion
Installing a one arm toilet paper holder is a simple and straightforward process that can help enhance the functionality and style of your bathroom. By following the steps we’ve outlined in this guide, you can install a toilet paper holder that will last for years to come.
To recap, start by gathering all the necessary materials and tools, locate the studs or install drywall anchors, and attach the holder to the screws or anchors. Remember to ensure that the holder is level to prevent the toilet paper roll from falling off.
Finally, here are some additional tips for maintaining your one arm toilet paper holder:
- Clean the holder regularly with a damp cloth to remove any dust or debris.
- Avoid using abrasive or harsh chemicals that can damage the finish of the holder.
- Check the screws periodically to ensure that they’re tight and the holder is still securely attached to the wall.
By following these tips, you can keep your toilet paper holder looking great and functioning smoothly for years to come.
